News:

Attention: For security reasons,please choose a user name *different* from your login name.
Also make sure to choose a secure password and change it regularly.

Main Menu

Recent posts

#31
Trenz Electronic FPGA Modules / Problem with TEM0007 DDR setti...
Last post by cone83 - September 30, 2026, 11:12:26 AM
I have a TEM0007 and I struggle with DDR problems. Running memtester on the booted linux system alone works fine, but when I run a design in the fabric that reads from DDR at a high band width and processes it, I get memory corruption. No data is actually written to DDR from the fabric.

Sometimes the system runs stable, sometimes it's very unstable. This seems to be random and depend on the boot (so I guess it depends on the DDR training run). Some DDR settings seemed to improve stability (but due to the randomness I'm not 100% sure). Those settings are:

* Enabling advanced CA trainig
* Setting ADD/CMD drive to 48

Are there any known DDR problems for this module? I have experimented with different timing parameters, but haven't found a combination that would work reliably.

Any help is welcome,
Thanks
#32
Trenz Electronic FPGA Modules / Boot image compatibility betwe...
Last post by blee - September 30, 2026, 02:44:09 AM
Hi.
I built a image file for AMB0010 Base with TE0955-01 SOM using TE0955-te0955-rd-vivado_2024.2-build_1_20250707150046.zip

Can I use that image file for TEB0955-02 Base with TE0955-01 SOM directly ?

Thanks a lot
#33
UltraScale / ps_aux on TE0817
Last post by benm - September 23, 2026, 12:55:59 PM
Hello,
I have a problem powering up a TE0817 module:
LP_DCDC is 3.3V
3.3VIN is 3.3V
EN_LPD is 0
LP_0V85 is 0 as expected
DCDC_2V0 is 0 as expected
PS_PLL is 0 as expected
but
PS_AUX is 0.47V
PS_1V8 is 0.86V

I don't understand how this is happens. I don't use PS_1V8 on my carrier board, it is just connected to a power plane but nothing else is there.
Do you have a hint on what is going on?
Thanks,
Ben
#34
Trenz Electronic FPGA Modules / Re: Request for BOM Informatio...
Last post by YakameinTakashi - September 18, 2026, 04:30:35 AM
Martin-san,

Thank you so much!

Kind regards,

Takashi
#35
Trenz Electronic FPGA Modules / Re: Request for BOM Informatio...
Last post by Martin R @Trenz - September 17, 2026, 04:03:02 PM
Hi,
please write a short message with your request to support@trenz-electronic.de

Best regards
Martin
#36
Trenz Electronic FPGA Modules / Re: TE0820-04: custom Vivado d...
Last post by MA - September 17, 2026, 02:46:24 PM
Hi,

since the original Trenz reference design works correctly on your TE0820/TE0706, the module and carrier board are basically working as expected.

For the custom design, however, we would need to see the actual hardware configuration and the changes made compared to the reference design to determine what is causing the issue.

Therefore, please contact our support team at support@trenz-electronic.de with the details of your custom hardware design, configuration, and boot log, if available. This will give us a better opportunity to investigate the cause of the issue and compare your design with the reference design.

Best regards,
Manuela
#37
Trenz Electronic FPGA Modules / Re: TE0820 upgrading from 202...
Last post by MA - September 17, 2026, 02:36:13 PM
Hi,

we are currently developing the Vivado 2025.2 design for the TE0820, which is planned to be released within the next few weeks.
If you need a preliminary version before the official release, please contact our support team at support@trenz-electronic.de. We can provide a preliminary version if needed.

Best regards,
Manuela Strücker
#38
Trenz Electronic FPGA Modules / Request for BOM Information fo...
Last post by YakameinTakashi - September 17, 2026, 02:52:03 AM
Dear Trenz Electronic Team,

Thank you for your support.

Could you provide the BOM information for TE0818-02-BBE81-A?

Kind regards,

Takashi
T4952140
#39
Trenz Electronic FPGA Modules / Re: TE0720-04-61C33MA: ps7_ini...
Last post by Keisuke Sakai - September 01, 2026, 11:04:52 AM
Additional information:

I also tested the same TE0720 module with a TEBA0841-02 carrier board.

On the TEBA0841-02, ps7_init completes without any errors and the values of 0xF8000B40 and 0xF8000B44 change from 0x00000800 to 0x00000600, similarly to the behavior observed on the TE0703.

However, DDR still cannot be accessed afterwards:

--------------------------------------------------
On TEBA0841-02 (Failing)
--------------------------------------------------

mrd 0xF8000B40
F8000B40: 00000800

mrd 0xF8000B44
F8000B44: 00000800

mrd 0x00100000
Memory read error at 0x100000.
Cannot access DDR: the controller is held in reset

source {ps7_init.tcl}

ps7_init

mrd 0xF8000B40
F8000B40: 00000600

mrd 0xF8000B44
F8000B44: 00000600

mrd 0x00100000
Memory read error at 0x100000.
Cannot access DDR: the controller is held in reset

--------------------------------------------------

Therefore, there appear to be three different behaviors:

1. TE0703:
   - ps7_init succeeds
   - DDR becomes accessible

2. TEBA0841-02:
   - ps7_init succeeds
   - DDR remains inaccessible

3. Custom carrier:
   - ps7_init itself fails with
     "Invalid DAP IDCODE 00000000"

Since TEBA0841-02 is essentially a power-supply carrier, it seems possible that some boot-stage initialization (for example FSBL-related initialization) is not being executed. Could this explain why DDR remains in reset even though ps7_init completes successfully?

Kind regards,
K. Sakai
#40
Hi Ivan,

Greetings.

I sent an email to support@trenz-electronic.de on August 18, but I have not received a response yet.

Could you please help follow up with them or ping the team on my behalf?

Thank you for your assistance.

Kind regards,

Takashi