News:

Attention: For security reasons,please choose a user name *different* from your login name.
Also make sure to choose a secure password and change it regularly.

Main Menu

Recent posts

#11
Hi,
Quote from: martinius on October 15, 2026, 03:03:34 PMOh! thanks. I did not notice that so far. Then it is clear to me.
Is populating myself already an modification regarding warranty?

Note: these POF have to be soldered. Any case where you have to use a solder iron may affect warranty because it is often no more possible to figure out if a failure was already there before.
#12
Hi,
your statement '
As a side note, regarding the AMB0010-01 baseboard, there are two TE0790-03 units, and I connected Tera Term to the TE0790-03 unit wired to UART-1.' goes exactly in the right direction.
Currently it seems you don't have a boot failture (LEDs: red Done goes off and no Error LED lights up), you are only listing on the wrong terminal.
AMB0010 with the 'patches' for use with TE0955 module uses UART1 on J8. TEB0955 uses in standard configuration UART0 for FTDI USB to UART bridge.
So there are two options:
a) (Recommended) Recompile your design with different configuration/mapping: UART0 instead of UART1 for use with TEB0955.
b) Use UART1 on TEB0955 via not assembled pin header J14. Connect additional USB to UART converter to this pins. Please note UART1 pins are shared with CAN interface (standard use) on TEB0955 (Compare Schematic page 16). Therefore to make UART0 working without any interference with e.g. 'CAN Transmission Loopback' at least CAN_L, and CAN_H should be tied together or both pulled to GND (Add jumper at J28). This will set CAN_RX to a constant high state. Other option would be to disconnected by removing Transistors T1A/T1B or removing CAN Transceiver U21 completely!

Hope this helps understanding what is going on.
Best regards
#13
Trenz Electronic FPGA Modules / Re: Boot image compatibility b...
Last post by blee - October 16, 2026, 03:38:34 AM
Hi.
The board still does not boot.
(Boot switch=1(on), 2(off), 3(on), 4(off) and 12V power supply are used)

When I power on the TEB0955-02 baseboard, the LEDs on the TE0955-02 SOM turn on briefly and then turn off immediately)
And nothing is displayed on Tera Term.

As a side note, regarding the AMB0010-01 baseboard, there are two TE0790-03 units, and I connected Tera Term to the TE0790-03 unit wired to UART-1.
Could this be related to the current boot failure on the TEB0955?

Or Could you please provide further guidance or troubleshooting steps for this.
Thanks.
#14
MAX1000 community projects / Re: Playing ZX Spectrum in HDM...
Last post by martinius - October 15, 2026, 03:12:31 PM
I now found it on ALI!   Good advice.

Did you already try to get higher video rates?

#15
MAX1000 community projects / Re: Playing ZX Spectrum in HDM...
Last post by martinius - October 15, 2026, 03:08:00 PM
Quote from: Subcritical on March 23, 2025, 03:05:36 PMHDMI-PMOD:

Is this self built?

Generally interesting work.
#16
Trenz Electronic FPGA Modules / Re: TE 0725 series and transce...
Last post by martinius - October 15, 2026, 03:03:34 PM
Quote from: Vadim Y on October 15, 2026, 10:02:31 AMAMD Artix 7 doesn't have trancievers at all in CSG324 package.

Oh! thanks. I did not notice that so far. Then it is clear to me.

Quote from: Vadim Y on October 15, 2026, 10:10:13 AMYou can populate it yourself,
Is populating myself already an modification regarding warranty?




#17
Trenz Electronic FPGA Modules / Re: TE 0725 series and transce...
Last post by Vadim Y - October 15, 2026, 10:10:13 AM
Hi,

The LWL jack (fiber-optic connector) is an optional optical transceiver, type AFBR-59F2Z, which communicates with the FPGA via an LVDS interface. You can populate it yourself, or we can supply a module with the transceiver already assembled.

Please note that the warranty is void if you modify the module yourself.

https://docs.broadcom.com/doc/AV02-4756EN

Best Regards,
Vadim
#18
Trenz Electronic FPGA Modules / Re: TE 0725 series and transce...
Last post by Vadim Y - October 15, 2026, 10:02:31 AM
#19
Trenz Electronic FPGA Modules / Re: Boot image compatibility b...
Last post by MA - October 15, 2026, 09:03:34 AM
Hi,

and now its working or not?

br
#20
Trenz Electronic FPGA Modules / Re: Vivado 2020.2 board files ...
Last post by martinius - October 15, 2026, 02:44:32 AM
Quote from: bigguiness on January 17, 2023, 08:15:23 PMNote: Download location for boards from XHUB i

This is a fixed directory and cannot be changed. Typcially this is one drive C and points to the users APP directory here. Unhappily this is not allowed to be used by our IT.

I installed added another path at another drive and it worked. Make sure to point to the first directory top only to assign the path and not the particular file.