Attention: For security reasons,please choose a user name *different* from your login name.
Also make sure to choose a secure password and change it regularly.
spi@e000d000 {
clock-names = "ref_clk", "pclk";
clocks = <0x1 0xa 0x1 0x2b>;
compatible = "xlnx,zynq-qspi-1.0";
status = "okay";
interrupt-parent = <0x4>;
interrupts = <0x0 0x13 0x4>;
reg = <0xe000d000 0x1000>;
#address-cells = <0x1>;
#size-cells = <0x0>;
is-dual = <0x0>;
num-cs = <0x1>;
spi-rx-bus-width = <0x4>;
spi-tx-bus-width = <0x4>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0x0>;
#address-cells = <0x1>;
#size-cells = <0x1>;
spi-max-frequency = <0x2faf080>;
partition@0x00000000 {
label = "boot";
reg = <0x0 0x500000>;
};
partition@0x00500000 {
label = "bootenv";
reg = <0x500000 0x20000>;
};
partition@0x00520000 {
label = "kernel";
reg = <0x520000 0xc10000>;
};
partition@0x01130000 {
label = "data";
reg = <0x1130000 0xed0000>;
};
};
};
[2023-11-21 11:32:17.373] Hit any key to stop autoboot: 0
[2023-11-21 11:32:17.376] Warning: SPI speed fallback to 100 kHz
[2023-11-21 11:32:17.380] SF: Detected n25q256 with page size 256 Bytes, erase size 4 KiB, total 32 MiB
[2023-11-21 11:32:17.387] device 0 offset 0x520000, size 0xc10000
[2023-11-21 11:32:21.448] SF: 12648448 bytes @ 0x520000 Read: OK
[2023-11-21 11:37:46.725] Zynq> sf probe 0 50000000
[2023-11-21 11:37:54.960] SF: Detected n25q256 with page size 256 Bytes, erase size 4 KiB, total 32 MiB
[2023-11-21 11:37:54.968] Zynq> boot
[2023-11-21 11:38:01.401] SF: Detected n25q256 with page size 256 Bytes, erase size 4 KiB, total 32 MiB
[2023-11-21 11:38:01.407] device 0 offset 0x520000, size 0xc10000
[2023-11-21 11:38:03.446] SF: 12648448 bytes @ 0x520000 Read: OK
[2023-11-21 11:39:10.933] Zynq> sf probe 100000
[2023-11-21 11:39:21.905] SF: Detected n25q256 with page size 256 Bytes, erase size 4 KiB, total 32 MiB
[2023-11-21 11:39:21.912] Zynq> boot
[2023-11-21 11:39:25.408] SF: Detected n25q256 with page size 256 Bytes, erase size 4 KiB, total 32 MiB
[2023-11-21 11:39:25.415] device 0 offset 0x520000, size 0xc10000
[2023-11-21 11:39:29.477] SF: 12648448 bytes @ 0x520000 Read: OK
Quote from: JH on November 04, 2022, 08:46:33 AMWhich was working fine.Thank so much.
Hi,
can you try out our 21.2 template with our prebuilt xsa files, this should works:
https://wiki.trenz-electronic.de/display/PD/TE0808+StarterKit Run 3
Template project is in:
https://wiki.trenz-electronic.de/display/PD/TE0808+StarterKit#TE0808StarterKit-DesignSources
copy xsa from prebuilt folder to the petalinux folder and start with point 3 "petalinux-config --get-hw-description"
https://wiki.trenz-electronic.de/display/PD/PetaLinux+KICKstart#PetaLinuxKICKstart-CreatingaProjectfromVivadoProject
in case this doesn't work, check your build environment.
https://wiki.trenz-electronic.de/display/PD/PetaLinux+KICKstart#PetaLinuxKICKstart-PetaLinuxInstallation
I use Ubuntu 20.4 on WSL which was working fine.
br
John
Page created in 0.052 seconds with 15 queries.