Author Topic: Eddy-CPU DK v2.5 standard terminal output at boot time  (Read 10084 times)


  • Jr. Member
  • **
  • Posts: 54
Eddy-CPU DK v2.5 standard terminal output at boot time
« on: May 30, 2011, 11:40:20 AM »
What is the standard debug-port output for a SystemBase Eddy-CPU DK v2.5 at boot time?

If you connect a serial cable to the D-sub 9 debug-port, you should detect the following output trace in your terminal emulator (115200 / 8 / n / 1) when you turn on the SystemBase Eddy-CPU DK v2.5. Flow control setting is irrelevant.
Important: turn ON both switches on switch S6 (NAND Flash  chip select + data Flash chip select):

Code: [Select]
NAND:  256 MiB
Hit any key to stop autoboot:  0
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.21 (root@linuxdev) (gcc version 4.1.1) #66 PREEMPT Wed Sep 15 18:10:03 KST 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: Atmel AT91SAM9260-EK
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists.  Total pages: 8128
Kernel command line: root=/dev/ram rw console=ttyS0,115200,mem=32M
AT91: 96 gpio irqs in 3 banks
PID hash table entries: 128 (order: 7, 512 bytes)
AT91 timer period: 82559
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 26284KB available (3064K code, 255K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
BUG: at kernel/sched.c:4303 __schedule()
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 3, 36864 bytes)
TCP bind hash table entries: 1024 (order: 2, 28672 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
checking if image is isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2720K
NetWinder Floating Point Emulator V0.97 (double precision)
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 226, nTxLock = 1813
yaffs Sep 15 2010 10:57:26 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
at91sam9_wdt: invalid timeout (must be between 1 and 16)
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
atmel_usart.3: ttyS3 at MMIO 0xfffb8000 (irq = 8) is a ATMEL_SERIAL
atmel_usart.4: ttyS4 at MMIO 0xfffd0000 (irq = 23) is a ATMEL_SERIAL
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
macb macb: detected PHY at address 0 (ID 0022:1513)
eth0: Atmel MACB at 0xfffc4000 irq 21 (00:00:00:00:00:00)
SCSI Media Changer driver v0.25
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)
mtd_dataflash spi0.1: EN25Q64 (8192 Kbytes)
Creating 6 MTD partitions on "spi0.1":
0x00000000-0x00010000 : "Bootstrap"
0x00010000-0x00020000 : "BootLoaderenv"
0x00020000-0x00050000 : "BootLoader"
0x00050000-0x00280000 : "OS"
0x00280000-0x00700000 : "Root Filesystem"
0x00700000-0x00800000 : "Config Filesystem"
atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffcc000 (irq 13)
116x: driver isp116x-hcd, 03 Nov 2005
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 20, io mem 0x00500000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usb 1-1: new full speed USB device using at91_ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new full speed USB device using at91_ohci and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
udc: at91_udc version 3 May 2006
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
at91_i2c at91_i2c: AT91 i2c bus driver.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <>
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 108K
at91sam9_wdt: Watchdog register already programmed.
<        Network configurations       >
Server Name   Eddy
Link Type     Static IP
IP Address
eth0: link down
-n Initializing random number generator...
ds1307 0-0068: rtc core: registered ds1307 as rtc0
Product ID = Eddy-CPU
scsi 0:0:0:0: Direct-Access     Multi    Flash Reader     1.00 PQ: 0 ANSI: 0
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
fb0: cfag12864b frame buffer device
RTC = 2000-08-25 20:23:15
« Last Edit: May 30, 2011, 12:11:44 PM by Hengist »