Validation failed for parameter 'PSU UIPARAM DDR CWL(PSU__DDRC__CWL)'

[Yourguen023]

Hi,

I'm new in the FPGA field, so please be exhaustive in your explanations.

I'm trying to use a Trenz TEBF0808 +Trenz TE0808-04-6BE21-A. I use Vivado 2019.2 with Linux Ubuntu 18.04.4 LTS.
I downloaded TE0808-test_board_noprebuilt-vivado_2019.2-build_3_20200122142231 file.
I followed the instructions until the "Create Block Design".

I have the following errors in Vivado and have no idea how to solve it :

[IP_Flow 19-3478] Validation failed for parameter 'PSU UIPARAM DDR CWL(PSU__DDRC__CWL)' with value '16' for BD Cell 'zynq_ultra_ps_e_0'.  Supported CAS Write Latency for Speed Bin 2400  with Operating Freq 800 { 9 11 }

[IP_Flow 19-3478] Validation failed for parameter 'PSU UIPARAM DDR CL(PSU__DDRC__CL)' with value '17' for BD Cell 'zynq_ultra_ps_e_0'. Supported CAS Latency for Speed Bin 2400  with Operating Freq 800 { 12 }.This field does not need to be modified when Read DBI is enabled.

[IP_Flow 19-3478] Validation failed for parameter 'PSU UIPARAM DDR CWL(PSU__DDRC__CWL)' with value '16' for BD Cell 'zynq_ultra_ps_e_0'.  Supported CAS Write Latency for Speed Bin 2400  with Operating Freq 800 { 9 11 }

[BD 41-1273] Error running apply_rule TCL procedure: ERROR: [Common 17-39] 'set_property' failed due to earlier errors.
    ::xilinx.com_bd_rule_zynq_ultra_ps_e::apply_rule Line 29


If you can give me any leads.
Thank you in advance

[JH]

Hi,
do you have Vivado 2019.2 or Vivado 2019.2.1? In case without the patch, can you install 2019.2.1 patch (This is possible over Xilinx Information center)

I followed the instructions until the "Create Block Design".

Which of these step did you mean?
https://wiki.trenz-electronic.de/display/PD/TE0808+StarterKit#TE0808StarterKit-DesignFlow

The the BD design will be generated normally completely when you run "_create_linux_setup.sh" and start board selection guide.
--> can you send me the whole log file until the error occuress the vivado.log file will be generated in the subfolder ../StarterKit/v_log

PS: we offer the design also with prebuilt binaries to test the board directly.

br
John

[Yourguen023]

do you have Vivado 2019.2 or Vivado 2019.2.1? In case without the patch, can you install 2019.2.1 patch (This is possible over Xilinx Information center)

I have Vivado 2019.2. Next the board implementation, I have to install Petalinux and the version I use is 2019.2. Won't that interfere? (Petalinus 2019.2 works with Vivado 2019.2.1 ?)

Which of these step did you mean?
https://wiki.trenz-electronic.de/display/PD/TE0808+StarterKit#TE0808StarterKit-DesignFlow

Yes, exactly this document, sorry.

The the BD design will be generated normally completely when you run "_create_linux_setup.sh" and start board selection guide.

Ah... So my generation wasn't complete. I thought it was.

--> can you send me the whole log file until the error occuress the vivado.log file will be generated in the subfolder ../StarterKit/v_log

Attached, the log file.

PS: we offer the design also with prebuilt binaries to test the board directly.

I probably missed it, I'll try to find it and test the bord with it. 

Thank you very much for your help.

BR
Camille

[Yourguen023]

I finally found the binaries:

https://www.trenz-electronic.de/fileadmin/docs/Trenz_Electronic/Modules_and_Module_Carriers/5.2x7.6/TE0808/Reference_Design/2019.2/StarterKit/TE0808-StarterKit-vivado_2019.2-build_8_20200325083436.zip

\Downloads\TE0808-StarterKit-vivado_2019.2-build_8_20200325083436\StarterKit\prebuilt\boot_images\

Either way, as I'm new in the FPGA field and I would like to learn (especially from errors I made), I would be very pleased to know what is my mistake for the Vivado Project Generation.

BR
Camille

[JH]

Hi,
I've checked your log file.
this looks like some vivado problem with your OS:

WARNING: [Common 17-1496] Vivado tclapp support version doesn't have install/uninstall hooks. Please update support using ::tclapp::update_support command.
....
xterm: Xt error: Can't open display: :0

which kind of linux did you use? On which is supported by Xilinx --> You can check requirements on xilinx installation guide for your version.

(Petalinus 2019.2 works with Vivado 2019.2.1 ?)

yes this works, important is both is 2019.2.

br
John

[Yourguen023]

Finally, I've used the prebuilt file to program the FPGA and to temporarily avoid the issue. I didn't install the 2019.2.1 patch. All was right until Vitis step.

I had 2 issues in Vitis :
1 ) I wasn't able to connect to any of the serial ports.

Solution :
sudo adduser #username dialout
sudo user mod -a -G dialout #username
reboot (very important!)

2 ) Error Lauchning the Program

Could not find ARM device on the board for connection 'Local'.
Check is the target is in :
1. Split JTAG - No operations are possible with ARM DAP.
2. Non JTAG bootmode - Bootrom may need time to enable DAP.

Solution :
cd /tools/Xilinx/Vivado/2019.2/data/xicom/cable-drivers/lin64/install_script/
sudo ./install-drivers

Everything works, I have the "Hello World" message.

Suprisingly, I don't have the 'PSU UIPARAM DDR CWL(PSU__DDRC__CWL)' issue any more.

Thank you JH