Print Page - TE0802 SATA configuration

Title: TE0802 SATA configuration
Post by: pablo_controlpaths on October 01, 2020, 07:45:28 PM

Hello,
I am trying to connect a SATA SSD to the m.2 connector of TE0802 board, but, when linux boots, a repetitive message appear that says

Code Select

ata1 sata link down (sstatus 1 scontrol 330)
On vivado, I have enabled the SATA connection to lane0, and I am using the refclock0 at 150mhz.
My system-user.dtsi

Code Select

/include/ "system-conf.dtsi"
/ {
};

#include <dt-bindings/phy/phy.h>

&sata {
	status = "okay";
	phys = <&lane0 PHY_TYPE_SATA 0 0 150000000>;
};

&serdes {
	status = "okay";
};

Is anything wrong? or maybe there are any else that I have to add?
Thanks
Greetings

Title: Re: TE0802 SATA configuration
Post by: JH on October 02, 2020, 09:16:47 AM

Hi,
we offer reference design with documentation, sources and prebuilt binaries:
https://wiki.trenz-electronic.de/display/PD/TE0802+Test+Board

But TE0802 hasn't any SATA connector.

Can it be that you want to use M.2 SSD PCIe?
https://wiki.trenz-electronic.de/display/PD/TE0802+TRM#TE0802TRM-MainComponents
In this case you must use correct M.2 Card. You must use this one which PCIe Interface, we have some lists with tested cards:
https://wiki.trenz-electronic.de/pages/viewpage.action?pageId=105162633

Br
John

Title: Re: TE0802 SATA configuration
Post by: pablo_controlpaths on October 02, 2020, 09:28:41 AM

Hello, thanks for reply.

I have connected a SATA SSD to the m.2 connector. Then, on block design, I have disabled the PCI on lane 0, and I have enabled for this lane the SATA interface. I think I can do that without problems, isn't right?

The SSD I am using is this Samsung SSD0E38395 MZ-NTE2560.

Greetings.

Title: Re: TE0802 SATA configuration
Post by: JH on October 02, 2020, 10:41:50 AM

QuoteI think I can do that without problems, isn't right?

maybe, but I would not say without problems. It's not designed for also this M2 Slot is PCIe not Sata --> I know some keyings can be theoretical compatible and ZynqMP supports both. But I would still suggest to use PCIe memory card from the list from my last post.

But why try out still SATA, check also selected Reference CLKs and what's really on the GTR REF CLK Pin.
See schematics and TRM:
https://shop.trenz-electronic.de/en/TE0802-02-2AEU2-A-MPSoC-Development-Board-with-Xilinx-Zynq-UltraScale-ZU2-and-LPDDR4?path=Trenz_Electronic/Development_Boards/TE0802/REV02/Documents
https://wiki.trenz-electronic.de/display/PD/TE0802+TRM#TE0802TRM-ClockGenerator

br
John

Title: Re: TE0802 SATA configuration
Post by: pablo_controlpaths on October 04, 2020, 10:26:33 AM

As I see, the M.2 socket is connected to the refclk0, like my device tree. I think I used the words without problem very easily. The only reason to use a sata SSD is because I had one on my lab, but I will use a PCI of the list instead.

Thanks!

Title: Re: TE0802 SATA configuration
Post by: JH on October 05, 2020, 07:10:26 AM

Hi,
in your device tree (and I think also in your PS IP), you has setup 150MHz REFCLK, but the REFCLK which is available is 100MHz.

br
John

Trenz Electronic GmbH Support Forum

Trenz Electronic Products => Trenz Electronic FPGA Modules => Topic started by: pablo_controlpaths on October 01, 2020, 07:45:28 PM