U-Boot 2014.07 (Jul 01 2020 - 09:42:07)

DRAM:  ECC disabled 512 MiB
MMC:   zynq_sdhci: 0
SF: Detected S25FL256S_64K with page size 256 Bytes, erase size 64 KiB, total 32 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   Gem.e000b000
U-BOOT for prototype

Gem.e000b000 Waiting for PHY auto negotiation to complete..... done
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5

Retry count exceeded
Hit any key to stop autoboot:  4  3  2  1  0 
SF: Detected S25FL256S_64K with page size 256 Bytes, erase size 64 KiB, total 32 MiB
SF: 11010048 bytes @ 0x4343c0 Read: OK
## Loading kernel from FIT Image at 01000000 ...
   Using 'conf@1' configuration
   Trying 'kernel@1' kernel subimage
     Description:  PetaLinux Kernel
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x010000f0
     Data Size:    9379412 Bytes = 8.9 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x00008000
     Entry Point:  0x00008000
     Hash algo:    crc32
     Hash value:   f6b1f4e8
   Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 01000000 ...
   Using 'conf@1' configuration
   Trying 'fdt@1' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x018f2028
     Data Size:    17763 Bytes = 17.3 KiB
     Architecture: ARM
     Hash algo:    crc32
     Hash value:   14a7d0d5
   Verifying Hash Integrity ... crc32+ OK
   Booting using the fdt blob at 0x18f2028
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 07ff8000, end 07fff562 ... OK

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 3.17.0-xilinx (user@wfx01550) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #2 SMP PREEMPT Wed Jul 1 09:43:39 CEST 2020
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: prototype
cma: Reserved 128 MiB at 18000000
Memory policy: Data cache writealloc
PERCPU: Embedded 8 pages/cpu @57b9c000 s8704 r8192 d15872 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyPS0,115200 earlyprintk
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 375532K/524288K available (4631K kernel code, 239K rwdata, 1592K rodata, 6068K init, 210K bss, 148756K reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
    vmalloc : 0x60800000 - 0xff000000   (2536 MB)
    lowmem  : 0x40000000 - 0x60000000   ( 512 MB)
    pkmap   : 0x3fe00000 - 0x40000000   (   2 MB)
    modules : 0x3f000000 - 0x3fe00000   (  14 MB)
      .text : 0x40008000 - 0x4061c1b0   (6225 kB)
      .init : 0x4061d000 - 0x40c0a200   (6069 kB)
      .data : 0x40c0c000 - 0x40c47ea0   ( 240 kB)
       .bss : 0x40c47ea0 - 0x40c7c7ac   ( 211 kB)
Preemptible hierarchical RCU implementation.
	Dump stacks of tasks blocking RCU-preempt GP.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
L2C: platform provided aux values match the hardware, so have no effect.  Please remove them.
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76360001
slcr mapped to 60804000
zynq_clock_init: clkc starts at 60804100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
timer #0 at 60806000, irq=43
Console: colour dummy device 80x30
Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x460308 - 0x460360
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0x60880000
VCCPINT: 1000 mV 
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 989
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-2364208
dma-pl330 f8003000.dmac: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 59, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
e0001000.serial: ttyPS1 at MMIO 0xe0001000 (irq = 82, base_baud = 6249999) is a xuartps
xdevcfg f8007000.devcfg: ioremap 0xf8007000 to 6086c000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
xilinx_spi 41e00000.axi_quad_spi: at 0x41E00000 mapped to 0x608e0000, irq=62
xilinx_spi 41e10000.axi_quad_spi: at 0x41E10000 mapped to 0x60900000, irq=64
xilinx_spi 41e20000.axi_quad_spi: at 0x41E20000 mapped to 0x60920000, irq=63
m25p80 spi32763.0: found s25fl256s1, expected n25q128a13
m25p80 spi32763.0: s25fl256s1 (32768 Kbytes)
4 ofpart partitions found on MTD device spi32763.0
Creating 4 MTD partitions on "spi32763.0":
0x000000000000-0x0000004143c0 : "boot"
mtd: partition "boot" doesn't end on an erase block -- force read-only
0x0000004143c0-0x0000004343c0 : "bootenv"
mtd: partition "bootenv" doesn't start on an erase block boundary -- force read-only
0x0000004343c0-0x000000eb43c0 : "kernel"
mtd: partition "kernel" doesn't start on an erase block boundary -- force read-only
0x000000eb43c0-0x000002000000 : "spare"
mtd: partition "spare" doesn't start on an erase block boundary -- force read-only
CAN device driver interface
e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
libphy: XEMACPS mii bus: probed
xemacps e000b000.ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at 60872000 with timeout 10s
zynq-edac f8006000.memory-controller: ecc not enabled
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
sdhci-arasan e0101000.sdhci: No vmmc regulator found
sdhci-arasan e0101000.sdhci: No vqmmc regulator found
mmc0: SDHCI controller on e0101000.sdhci [e0101000.sdhci] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
Registering SWP/SWPB emulation handler
/opt/pkg/petalinux-v2014.4-final/components/linux-kernel/xlnx-3.17/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
Freeing unused kernel memory: 6068K (4061d000 - 40c0a000)

INIT: version 2.88 bootingmmc0: BKOPS_EN bit is not set
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 8GTF4R 7.28 GiB 
mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB
 mmcblk0:
 mmcblk0boot1: unknown partition table
 mmcblk0boot0: unknown partition table


Creating /dev/flash/* device nodes

random: dd urandom read with 22 bits of entropy available
starting Busybox inet Daemon: inetd... done.

update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing)

 Removing any system startup links for run-postinsts ...

  /etc/rcS.d/S99run-postinsts


INIT: Entering runlevel: 5


Configuring network interfaces... udhcpc (v1.22.1) started

Sending discover...

Sending discover...

xemacps e000b000.ethernet: Set clk to 0 Hz
xemacps e000b000.ethernet: link up (100/FULL)
Sending discover...

No lease, forking to background

done.

Starting Dropbear SSH server: Generating key, this may take a while...

Public key portion is:

ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQC1sYtFFxIro/CpffuYLDVbZIxCj5gVPFgQF0ycU7aHpK0Reqqbdc1FwiG1Oviz9qmeWacE+q4SBnCdCgSl853renVgRU9U4En6OAkOcqQhd483y5C6ZxA71GMRvyxWTz7bLPLXorF4dSidM4x7jIqAcTwFZrwRQpXZ5dTvt/BDHmdLYd8bh5JTRslXj2tt/24InHcXDc1x0msYa7/woors2rsdO0dyKAggw8ukkDiQ+V8SScWJG4V5IArBMrZy9mMNc1DncKftKXnHKYpGyo6QGW27avRIPGxicRXdmIjUqU+4o/f4AZqv3eN0sOL/XytLhKH6yDgXOK7XanekCTh3 root@prototype

Fingerprint: md5 00:46:8c:e5:74:2e:e8:46:d6:a7:c6:0f:89:95:25:e9

NET: Registered protocol family 10
dropbear.

Starting syslogd/klogd: done

Sun Jan  1 00:00:00 UTC 2017
