Xilinx Zynq MP First Stage Boot Loader 

Release 2018.2   Aug  6 2018  -  13:41:46

--------------------------------------------------------------------------------
TE0808 Board Initialisation
PCIe Reset Complete

--------------------------------------------------------------------------------
NOTICE:  ATF running on XCZU9EG/silicon v4/RTL5.1 at 0xfffea000
NOTICE:  BL31: Secure code at 0x0
NOTICE:  BL31: Non secure code at 0x8000000
NOTICE:  BL31: v1.4(release):xilinx-v2018.1-4-g93a69a5a
NOTICE:  BL31: Built : 21:02:14, Jul 30 2018
PMUFW:	v1.0


U-Boot 2018.01 (Jul 31 2018 - 11:03:22 -0400) Xilinx ZynqMP ZCU102 rev1.0

I2C:   ready
DRAM:  4 GiB
EL Level:	EL2
Chip ID:	zu9eg
MMC:   sdhci@ff160000: 0 (eMMC), sdhci@ff170000: 1 (SD)
SF: Detected n25q512a with page size 512 Bytes, erase size 128 KiB, total 128 MiB
*** Warning - bad CRC, using default environment

In:    serial@ff000000
Out:   serial@ff000000
Err:   serial@ff000000
Board: Xilinx ZynqMP
Bootmode: SD_MODE1
Net:   ZYNQ GEM: ff0e0000, phyaddr 1, interface rgmii-id
eth0: ethernet@ff0e0000
U-BOOT for USB3_Test

ethernet@ff0e0000 Waiting for PHY auto negotiation to complete....... done
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.42.0.143 (2796 ms)
Hit any key to stop autoboot:  4  3  2  1  0 
Device: sdhci@ff160000
Manufacturer ID: 13
OEM: 14e
Name: Q2J54 
Tran Speed: 200000000
Rd Block Len: 512
MMC version 5.0
High Capacity: Yes
Capacity: 3.6 GiB
Bus Width: 4-bit
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.6 GiB WRREL
Boot Capacity: 16 MiB ENH
RPMB Capacity: 512 KiB ENH
reading image.ub
13377672 bytes read in 866 ms (14.7 MiB/s)
## Loading kernel from FIT Image at 10000000 ...
   Using 'conf@system-top.dtb' configuration
   Trying 'kernel@1' kernel subimage
     Description:  Linux kernel
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x10000104
     Data Size:    6929117 Bytes = 6.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00080000
     Entry Point:  0x00080000
     Hash algo:    sha1
     Hash value:   297f3925f3d661f2336552143c1b518ab1a288af
   Verifying Hash Integrity ... sha1+ OK
## Loading ramdisk from FIT Image at 10000000 ...
   Using 'conf@system-top.dtb' configuration
   Trying 'ramdisk@1' ramdisk subimage
     Description:  petalinux-user-image
     Type:         RAMDisk Image
     Compression:  gzip compressed
     Data Start:   0x106a3e60
     Data Size:    6413463 Bytes = 6.1 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: unavailable
     Entry Point:  unavailable
     Hash algo:    sha1
     Hash value:   f63c9b4180324a26beb0a74f69fad96c7460f3ed
   Verifying Hash Integrity ... sha1+ OK
## Loading fdt from FIT Image at 10000000 ...
   Using 'conf@system-top.dtb' configuration
   Trying 'fdt@system-top.dtb' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x1069bce8
     Data Size:    32948 Bytes = 32.2 KiB
     Architecture: AArch64
     Hash algo:    sha1
     Hash value:   7c0a626f87910706a8d538cb7c9ad5a22d72307b
   Verifying Hash Integrity ... sha1+ OK
   Booting using the fdt blob at 0x1069bce8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 079e2000, end 07fffc97 ... OK
   Loading Device Tree to 00000000079d6000, end 00000000079e10b3 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #4 SMP Tue Jul 31 11:07:05 EDT 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Machine model: xlnx,zynqmp
[    0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')
[    0.000000] bootconsole [cdns0] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 256 MiB at 0x000000006fc00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff76000 s45976 r8192 d31848 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1033987
[    0.000000] Kernel command line: earlycon clk_ignore_unused
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff]
[    0.000000] Memory: 3778412K/4193280K available (9916K kernel code, 642K rwdata, 3112K rodata, 512K init, 2165K bss, 152724K reserved, 262144K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008a30000   (  9920 KB)
[    0.000000]     .rodata : 0xffffff8008a30000 - 0xffffff8008d40000   (  3136 KB)
[    0.000000]       .init : 0xffffff8008d40000 - 0xffffff8008dc0000   (   512 KB)
[    0.000000]       .data : 0xffffff8008dc0000 - 0xffffff8008e60a00   (   643 KB)
[    0.000000]        .bss : 0xffffff8008e60a00 - 0xffffff800907e0b0   (  2166 KB)
[    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000]               0xffffffbf00000000 - 0xffffffbf1dc00000   (   476 MB actual)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc880000000   ( 34816 MB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU event tracing is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 33.33MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7b00c3c70, max_idle_ns: 440795203803 ns
[    0.000003] sched_clock: 56 bits at 33MHz, resolution 30ns, wraps every 2199023255540ns
[    0.008228] Console: colour dummy device 80x25
[    0.012480] console [tty0] enabled
[    0.015847] bootconsole [cdns0] disabled
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.0-xilinx-v2018.2 (oe-user@oe-host) (gcc version 7.2.0 (GCC)) #4 SMP Tue Jul 31 11:07:05 EDT 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Machine model: xlnx,zynqmp
[    0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')
[    0.000000] bootconsole [cdns0] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 256 MiB at 0x000000006fc00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] percpu: Embedded 21 pages/cpu @ffffffc87ff76000 s45976 r8192 d31848 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1033987
[    0.000000] Kernel command line: earlycon clk_ignore_unused
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB [mem 0x6bc00000-0x6fc00000] (64MB) mapped at [ffffffc06bc00000-ffffffc06fbfffff]
[    0.000000] Memory: 3778412K/4193280K available (9916K kernel code, 642K rwdata, 3112K rodata, 512K init, 2165K bss, 152724K reserved, 262144K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008a30000   (  9920 KB)
[    0.000000]     .rodata : 0xffffff8008a30000 - 0xffffff8008d40000   (  3136 KB)
[    0.000000]       .init : 0xffffff8008d40000 - 0xffffff8008dc0000   (   512 KB)
[    0.000000]       .data : 0xffffff8008dc0000 - 0xffffff8008e60a00   (   643 KB)
[    0.000000]        .bss : 0xffffff8008e60a00 - 0xffffff800907e0b0   (  2166 KB)
[    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000]               0xffffffbf00000000 - 0xffffffbf1dc00000   (   476 MB actual)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc880000000   ( 34816 MB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU event tracing is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 33.33MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7b00c3c70, max_idle_ns: 440795203803 ns
[    0.000003] sched_clock: 56 bits at 33MHz, resolution 30ns, wraps every 2199023255540ns
[    0.008228] Console: colour dummy device 80x25
[    0.012480] console [tty0] enabled
[    0.015847] bootconsole [cdns0] disabled
[    0.019756] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=133333)
[    0.019768] pid_max: default: 32768 minimum: 301
[    0.019862] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.019878] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.020424] ASID allocator initialised with 65536 entries
[    0.020472] Hierarchical SRCU implementation.
[    0.020727] EFI services will not be available.
[    0.020749] zynqmp_plat_init Platform Management API v1.0
[    0.020757] zynqmp_plat_init Trustzone version v1.0
[    0.020849] smp: Bringing up secondary CPUs ...
[    0.021079] Detected VIPT I-cache on CPU1
[    0.021106] CPU1: Booted secondary processor [410fd034]
[    0.021357] Detected VIPT I-cache on CPU2
[    0.021373] CPU2: Booted secondary processor [410fd034]
[    0.021615] Detected VIPT I-cache on CPU3
[    0.021632] CPU3: Booted secondary processor [410fd034]
[    0.021669] smp: Brought up 1 node, 4 CPUs
[    0.021698] SMP: Total of 4 processors activated.
[    0.021705] CPU features: detected feature: 32-bit EL0 Support
[    0.021715] CPU: All CPU(s) started at EL2
[    0.021729] alternatives: patching kernel code
[    0.022403] devtmpfs: initialized
[    0.025354] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0
[    0.025485] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.025506] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.030472] xor: measuring software checksum speed
[    0.067826]    8regs     :  2526.000 MB/sec
[    0.107853]    8regs_prefetch:  2252.000 MB/sec
[    0.147884]    32regs    :  3105.000 MB/sec
[    0.187909]    32regs_prefetch:  2610.000 MB/sec
[    0.187917] xor: using function: 32regs (3105.000 MB/sec)
[    0.187984] pinctrl core: initialized pinctrl subsystem
[    0.188161] random: fast init done
[    0.188476] NET: Registered protocol family 16
[    0.189236] vdso: 2 pages (1 code @ ffffff8008a36000, 1 data @ ffffff8008dc4000)
[    0.189251] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.189670] DMA: preallocated 256 KiB pool for atomic allocations
[    0.217881] reset_zynqmp reset-controller: Xilinx zynqmp reset driver probed
[    0.218391] ARM CCI_400_r1 PMU driver probed
[    0.222129] zynqmp-pinctrl ff180000.pinctrl: zynqmp pinctrl initialized
[    0.228499] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.296179] raid6: int64x1  gen()   441 MB/s
[    0.364236] raid6: int64x1  xor()   490 MB/s
[    0.432306] raid6: int64x2  gen()   754 MB/s
[    0.500305] raid6: int64x2  xor()   662 MB/s
[    0.568387] raid6: int64x4  gen()  1144 MB/s
[    0.636418] raid6: int64x4  xor()   814 MB/s
[    0.704481] raid6: int64x8  gen()  1075 MB/s
[    0.772567] raid6: int64x8  xor()   818 MB/s
[    0.840647] raid6: neonx1   gen()   796 MB/s
[    0.908679] raid6: neonx1   xor()   935 MB/s
[    0.976732] raid6: neonx2   gen()  1282 MB/s
[    1.044802] raid6: neonx2   xor()  1324 MB/s
[    1.112880] raid6: neonx4   gen()  1653 MB/s
[    1.180927] raid6: neonx4   xor()  1582 MB/s
[    1.248991] raid6: neonx8   gen()  1813 MB/s
[    1.317037] raid6: neonx8   xor()  1682 MB/s
[    1.317044] raid6: using algorithm neonx8 gen() 1813 MB/s
[    1.317051] raid6: .... xor() 1682 MB/s, rmw enabled
[    1.317057] raid6: using neon recovery algorithm
[    1.317813] SCSI subsystem initialized
[    1.317963] usbcore: registered new interface driver usbfs
[    1.317997] usbcore: registered new interface driver hub
[    1.318031] usbcore: registered new device driver usb
[    1.318088] media: Linux media interface: v0.10
[    1.318111] Linux video capture interface: v2.00
[    1.318146] pps_core: LinuxPPS API ver. 1 registered
[    1.318153] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.318171] PTP clock support registered
[    1.318194] EDAC MC: Ver: 3.0.0
[    1.318477] zynqmp-ipi ff9905c0.mailbox: Probed ZynqMP IPI Mailbox driver.
[    1.318595] FPGA manager framework
[    1.318687] fpga-region fpga-full: FPGA Region probed
[    1.318761] Advanced Linux Sound Architecture Driver Initialized.
[    1.318989] Bluetooth: Core ver 2.22
[    1.319010] NET: Registered protocol family 31
[    1.319017] Bluetooth: HCI device and connection manager initialized
[    1.319028] Bluetooth: HCI socket layer initialized
[    1.319037] Bluetooth: L2CAP socket layer initialized
[    1.319057] Bluetooth: SCO socket layer initialized
[    1.319528] clocksource: Switched to clocksource arch_sys_counter
[    1.319602] VFS: Disk quotas dquot_6.6.0
[    1.319642] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.323242] NET: Registered protocol family 2
[    1.323520] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    1.323722] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    1.324084] TCP: Hash tables configured (established 32768 bind 32768)
[    1.324147] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    1.324217] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    1.324358] NET: Registered protocol family 1
[    1.324585] RPC: Registered named UNIX socket transport module.
[    1.324594] RPC: Registered udp transport module.
[    1.324601] RPC: Registered tcp transport module.
[    1.324607] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.324699] Trying to unpack rootfs image as initramfs...
[    1.554453] Freeing initrd memory: 6260K
[    1.554788] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    1.554932] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.555540] audit: initializing netlink subsys (disabled)
[    1.555623] audit: type=2000 audit(1.543:1): state=initialized audit_enabled=0 res=1
[    1.555908] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[    1.556560] NFS: Registering the id_resolver key type
[    1.556579] Key type id_resolver registered
[    1.556586] Key type id_legacy registered
[    1.556597] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.556616] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.580690] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    1.580709] io scheduler noop registered
[    1.580716] io scheduler deadline registered
[    1.580741] io scheduler cfq registered (default)
[    1.580748] io scheduler mq-deadline registered
[    1.580755] io scheduler kyber registered
[    2.581376] nwl-pcie fd0e0000.pcie: PHY link never came up
[    2.581387] nwl-pcie fd0e0000.pcie: HW Initialization failed
[    2.581432] nwl-pcie: probe of fd0e0000.pcie failed with error -110
[    2.582107] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed
[    2.582443] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success
[    2.582578] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success
[    2.582709] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success
[    2.582841] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success
[    2.582971] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success
[    2.583107] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success
[    2.583243] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success
[    2.583374] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success
[    2.605830] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.608220] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.611888] brd: module loaded
[    2.615153] loop: module loaded
[    2.625963] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    2.625984] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst 
[    2.626914] scsi host0: ahci-ceva
[    2.627134] scsi host1: ahci-ceva
[    2.627236] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 36
[    2.627248] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 36
[    2.627392] mtdoops: mtd device (mtddev=name/number) must be supplied
[    2.628579] m25p80 spi0.0: n25q512a (131072 Kbytes)
[    2.628600] 3 ofpart partitions found on MTD device spi0.0
[    2.628607] Creating 3 MTD partitions on "spi0.0":
[    2.628617] 0x000000000000-0x000000100000 : "boot"
[    2.629017] 0x000000100000-0x000000140000 : "bootenv"
[    2.629358] 0x000000140000-0x000001740000 : "kernel"
[    2.630482] libphy: Fixed MDIO Bus: probed
[    2.631423] tun: Universal TUN/TAP device driver, 1.6
[    2.631594] CAN device driver interface
[    2.632574] macb ff0e0000.ethernet: Not enabling partial store and forward
[    2.632911] libphy: MACB_mii_bus: probed
[    2.703755] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 23 (00:0a:35:00:22:01)
[    2.703777] Marvell 88E1510 ff0e0000.ethernet-ffffffff:01: attached PHY driver [Marvell 88E1510] (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:01, irq=POLL)
[    2.704247] usbcore: registered new interface driver asix
[    2.704293] usbcore: registered new interface driver ax88179_178a
[    2.704322] usbcore: registered new interface driver cdc_ether
[    2.704351] usbcore: registered new interface driver net1080
[    2.704377] usbcore: registered new interface driver cdc_subset
[    2.704404] usbcore: registered new interface driver zaurus
[    2.704440] usbcore: registered new interface driver cdc_ncm
[    2.704704] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM
[    2.705013] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.705023] ehci-pci: EHCI PCI platform driver
[    2.705218] usbcore: registered new interface driver uas
[    2.705252] usbcore: registered new interface driver usb-storage
[    2.705656] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc0
[    2.705701] i2c /dev entries driver
[    2.706120] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 25
[    2.706457] i2c i2c-0: Added multiplexed i2c bus 1
[    2.706565] i2c i2c-0: Added multiplexed i2c bus 2
[    2.706681] i2c i2c-0: Added multiplexed i2c bus 3
[    2.706793] i2c i2c-0: Added multiplexed i2c bus 4
[    2.706904] i2c i2c-0: Added multiplexed i2c bus 5
[    2.707015] i2c i2c-0: Added multiplexed i2c bus 6
[    2.707682] i2c i2c-0: Added multiplexed i2c bus 7
[    2.707797] i2c i2c-0: Added multiplexed i2c bus 8
[    2.707807] pca954x 0-0073: registered 8 multiplexed busses for I2C switch pca9548
[    2.708041] i2c i2c-0: Added multiplexed i2c bus 9
[    2.708152] i2c i2c-0: Added multiplexed i2c bus 10
[    2.708264] i2c i2c-0: Added multiplexed i2c bus 11
[    2.708376] i2c i2c-0: Added multiplexed i2c bus 12
[    2.708488] i2c i2c-0: Added multiplexed i2c bus 13
[    2.708601] i2c i2c-0: Added multiplexed i2c bus 14
[    2.708716] i2c i2c-0: Added multiplexed i2c bus 15
[    2.708829] i2c i2c-0: Added multiplexed i2c bus 16
[    2.708839] pca954x 0-0077: registered 8 multiplexed busses for I2C switch pca9548
[    2.708939] IR NEC protocol handler initialized
[    2.708947] IR RC5(x/sz) protocol handler initialized
[    2.708953] IR RC6 protocol handler initialized
[    2.708960] IR JVC protocol handler initialized
[    2.708966] IR Sony protocol handler initialized
[    2.708972] IR SANYO protocol handler initialized
[    2.708979] IR Sharp protocol handler initialized
[    2.708985] IR MCE Keyboard/mouse protocol handler initialized
[    2.708992] IR XMP protocol handler initialized
[    2.709803] usbcore: registered new interface driver uvcvideo
[    2.709811] USB Video Class driver (1.1.1)
[    2.710255] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at ffffff80090f5000 with timeout 10s
[    2.710403] Bluetooth: HCI UART driver ver 2.3
[    2.710412] Bluetooth: HCI UART protocol H4 registered
[    2.710420] Bluetooth: HCI UART protocol BCSP registered
[    2.710445] Bluetooth: HCI UART protocol LL registered
[    2.710452] Bluetooth: HCI UART protocol ATH3K registered
[    2.710459] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.710495] Bluetooth: HCI UART protocol Intel registered
[    2.710503] Bluetooth: HCI UART protocol QCA registered
[    2.710538] usbcore: registered new interface driver bcm203x
[    2.710569] usbcore: registered new interface driver bpa10x
[    2.710600] usbcore: registered new interface driver bfusb
[    2.710630] usbcore: registered new interface driver btusb
[    2.710638] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[    2.710684] usbcore: registered new interface driver ath3k
[    2.710786] EDAC MC: ECC not enabled
[    2.710896] EDAC DEVICE0: Giving out device to module edac controller cache_err: DEV edac (POLLED)
[    2.711037] EDAC DEVICE1: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT)
[    2.711217] sdhci: Secure Digital Host Controller Interface driver
[    2.711225] sdhci: Copyright(c) Pierre Ossman
[    2.711231] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.755537] mmc0: SDHCI controller on ff160000.sdhci [ff160000.sdhci] using ADMA 64-bit
[    2.803531] mmc1: SDHCI controller on ff170000.sdhci [ff170000.sdhci] using ADMA 64-bit
[    2.809416] ledtrig-cpu: registered to indicate activity on CPUs
[    2.809543] usbcore: registered new interface driver usbhid
[    2.809551] usbhid: USB HID core driver
[    2.811154] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered
[    2.811983] pktgen: Packet Generator for packet performance testing. Version: 2.75
[    2.812549] Netfilter messages via NETLINK v0.30.
[    2.812659] ip_tables: (C) 2000-2006 Netfilter Core Team
[    2.817056] Initializing XFRM netlink socket
[    2.817111] NET: Registered protocol family 10
[    2.817539] Segment Routing with IPv6
[    2.817580] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    2.817767] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    2.818054] NET: Registered protocol family 17
[    2.818068] NET: Registered protocol family 15
[    2.818086] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.818099] Ebtables v2.0 registered
[    2.818185] can: controller area network core (rev 20170425 abi 9)
[    2.818216] NET: Registered protocol family 29
[    2.818230] can: raw protocol (rev 20170425)
[    2.818236] can: broadcast manager protocol (rev 20170425 t)
[    2.818247] can: netlink gateway (rev 20170425) max_hops=1
[    2.818419] Bluetooth: RFCOMM TTY layer initialized
[    2.818432] Bluetooth: RFCOMM socket layer initialized
[    2.818445] Bluetooth: RFCOMM ver 1.11
[    2.818454] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    2.818461] Bluetooth: BNEP filters: protocol multicast
[    2.818470] Bluetooth: BNEP socket layer initialized
[    2.818477] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.818486] Bluetooth: HIDP socket layer initialized
[    2.818582] 9pnet: Installing 9P2000 support
[    2.818600] Key type dns_resolver registered
[    2.818894] registered taskstats version 1
[    2.819177] Btrfs loaded, crc32c=crc32c-generic
[    2.821169] mmc0: new HS200 MMC card at address 0001
[    2.823879] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 39, base_baud = 6249999) is a xuartps
[    2.839834] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB 
[    2.844559] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[    2.848290] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[    2.855227] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB
[    2.859747] mmc1: new high speed SDHC card at address e624
[    2.863899] mmcblk1: mmc1:e624 SS08G 7.40 GiB (ro)
[    2.866129]  mmcblk1: p1 p2 p3
[    2.945645] ata2: SATA link down (SStatus 0 SControl 330)
[    2.946202] ata1: SATA link down (SStatus 0 SControl 330)
[    4.542071] console [ttyPS0] enabled
[    4.547893] xilinx-psgtr fd400000.zynqmp_phy: PLL lock time out
[    4.553736] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:8 protocol:4 pll_locked:no
[    4.561458] zynqmp-display fd4a0000.zynqmp-display: failed to lock pll
[    4.567979] zynqmp-display: probe of fd4a0000.zynqmp-display failed with error -110
[    4.575882] dwc3-of-simple ff9d0000.usb0: dwc3_simple_set_phydata: Can't find usb3-phy
[    4.584297] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.589714] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    4.597537] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x22010010
[    4.606182] xhci-hcd xhci-hcd.0.auto: irq 44, io mem 0xfe200000
[    4.612162] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.618869] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.626072] usb usb1: Product: xHCI Host Controller
[    4.630930] usb usb1: Manufacturer: Linux 4.14.0-xilinx-v2018.2 xhci-hcd
[    4.637614] usb usb1: SerialNumber: xhci-hcd.0.auto
[    4.642715] hub 1-0:1.0: USB hub found
[    4.646398] hub 1-0:1.0: 1 port detected
[    4.650442] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.655851] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    4.663528] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.671623] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    4.678328] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.685530] usb usb2: Product: xHCI Host Controller
[    4.690387] usb usb2: Manufacturer: Linux 4.14.0-xilinx-v2018.2 xhci-hcd
[    4.697072] usb usb2: SerialNumber: xhci-hcd.0.auto
[    4.702132] hub 2-0:1.0: USB hub found
[    4.705809] hub 2-0:1.0: 1 port detected
[    4.710518] rtc_zynqmp ffa60000.rtc: setting system clock to 2018-07-31 19:13:47 UTC (1533064427)
[    4.719414] clk: Not disabling unused clocks
[    4.723638] ALSA device list:
[    4.726541]   No soundcards found.
[    4.730296] Freeing unused kernel memory: 512K

INIT: version 2.88 booting

Starting udev
[    4.833726] udevd[1734]: starting version 3.2.2
[    4.842458] udevd[1735]: starting eudev-3.2.2
[    5.230264] EXT4-fs (mmcblk1p2): INFO: recovery required on readonly filesystem
[    5.237520] EXT4-fs (mmcblk1p2): write access unavailable, cannot proceed
[    5.247093] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities
[    5.258446] EXT2-fs (mmcblk1p2): error: couldn't mount because of unsupported optional features (244)
[    5.274821] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities
[    5.287663] EXT4-fs (mmcblk1p2): INFO: recovery required on readonly filesystem
[    5.294901] EXT4-fs (mmcblk1p2): write access unavailable, cannot proceed
[    5.302152] EXT2-fs (mmcblk1p2): error: couldn't mount because of unsupported optional features (244)
Starting internet superserver: inetd.

Configuring packages on first boot....

 (This may take several minutes. Please do not power off the machine.)

Running postinst /etc/rpm-postinsts/100-sysvinit-inittab...

update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing)

 Removing any s
INIT: Entering runlevel: 5


Configuring network interfaces... [    5.662653] pps pps0: new PPS source ptp0
[    5.666605] macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered.
[    5.673254] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.24.1) started

Sending discover...

[    8.635541] usb 1-1: new high-speed USB device number 2 using xhci-hcd
Sending discover...

[    8.787736] usb 1-1: New USB device found, idVendor=04b4, idProduct=650a
[    8.794361] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    8.811776] macb ff0e0000.ethernet eth0: link up (1000/Full)
[    8.817364] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.833497] hub 1-1:1.0: USB hub found
[    8.837279] hub 1-1:1.0: 4 ports detected
Sending discover...

Sending select for 10.42.0.143...

Lease of 10.42.0.143 obtained, lease time 3600

/etc/udhcpc.d/50default: Adding DNS 10.42.0.1

done.

Starting Dropbear SSH server: Generating key, this may take a while...

Public key portion is:

ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDDqY3EKjvIPCvema+jq8voqgR0Amodxd8+Gl1LP3ZbonQwlAZ7zLuF/aTQjVrG7CdKjmMTYcbIOJehiS9IxwDP+2W+gVRO4eXkp9hgpkACKJfW0pmkexuK/G4SIvTeKt+ZC9MzJDW8D4w7KwEtNVCkHzPsFtfQBfkw2nUIZN3BDqiXSyeRQR/CT5H/YWB7hRkblUP+j+4fIFavtAoCptLxIiS/FgiIWNyR1GUwU6evKJ2bXlxL9FjTLmvDdfNm2C+tvg/vES2qActYsJ13LF+Jh0JChjTsoc/s48Et+P83sqYinxgXOdDDgrHPsKFX3ahiYTXO89lMauwz59pgszDN root@USB3_Test

Fingerprint: md5 77:47:45:b4:08:fd:34:84:d9:7a:61:ae:96:c8:82:f5

dropbear.

Starting syslogd/klogd: done

Starting tcf-agent: OK


PetaLinux 2018.2 USB3_Test /dev/ttyPS0



USB3_Test login: root
Password: 
7[r[999;999H[6n8root@USB3_Test:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 001 Device 002: ID 04b4:650a
Bus 002 Device 001: ID 1d6b:0003
root@USB3_Test:~# df -h
Filesystem                Size      Used Available Use% Mounted on
devtmpfs                  1.8G      4.0K      1.8G   0% /dev
tmpfs                     1.9G    112.0K      1.9G   0% /run
tmpfs                     1.9G     76.0K      1.9G   0% /var/volatile
/dev/mmcblk1p1          511.7M     19.4M    492.3M   4% /run/media/mmcblk1p1
root@USB3_Test:~# 
root@USB3_Test:~# 