- Welcome to Trenz Electronic GmbH Support Forum.
Recent posts
#31
UltraScale / Re: First "Hello World" - JTAG...
Last post by Antti Lukats - May 28, 2025, 12:39:05 PMI can no see your screenshots, but at least your DIP switch settings are correct.
Did you try to access the JTAG chain with Vivado Hardware manager? Did it see the JTAG chain?
Did you try to access the JTAG chain with Vivado Hardware manager? Did it see the JTAG chain?
#32
MAX1000 community projects / Re: MAX1000 SDRAM chip
Last post by BR - May 27, 2025, 04:18:13 PMProblem indeed, anyways...
A lot of space on a MAX1000 board for a larger package and placing of those caps a little further from the chip.
Couldn't find another compatible high density sdram memory alternative in 8x8mm package.
Thanks for answering!
A lot of space on a MAX1000 board for a larger package and placing of those caps a little further from the chip.
Couldn't find another compatible high density sdram memory alternative in 8x8mm package.
Thanks for answering!
#33
UltraScale / First "Hello World" - JTAG err...
Last post by Meik - May 27, 2025, 12:54:28 PMHello,
we use a TE07005-04 connected with TE0820 for some first tests regarding MPSoCs and
try to run "Hello World" from the example project "TE0820-te0820-rd-vivado_2024.2-build_1_20250214171345".
Programming over JTAG we got some problems:
Vitis 2024.2 and Vitis Classic 2024.2 (Windows 11) shows the same problems. We connected PC-USB to Mini USB J7, set switches S4 (all to off) and S3 (1, 2, 4 to off; 3 to on).
Running debug "Launch hardware(Single Application Debug" we got following error message: jtag_err (appendix 1)
XSCT Console shows: info_XSCT_Console (appendix 2)
Clicking "Yes" shows: Running_Cortex (appendix 3)
Launching Debugger runs, shows message: FSBL_err (appendix 4) and ends with: Error_while_launching (appendix 5)
We never saw "Hello World". Do you see our Problem? What should we do?
With kindly regards,
Meik Hilse
we use a TE07005-04 connected with TE0820 for some first tests regarding MPSoCs and
try to run "Hello World" from the example project "TE0820-te0820-rd-vivado_2024.2-build_1_20250214171345".
Programming over JTAG we got some problems:
Vitis 2024.2 and Vitis Classic 2024.2 (Windows 11) shows the same problems. We connected PC-USB to Mini USB J7, set switches S4 (all to off) and S3 (1, 2, 4 to off; 3 to on).
Running debug "Launch hardware(Single Application Debug" we got following error message: jtag_err (appendix 1)
XSCT Console shows: info_XSCT_Console (appendix 2)
Clicking "Yes" shows: Running_Cortex (appendix 3)
Launching Debugger runs, shows message: FSBL_err (appendix 4) and ends with: Error_while_launching (appendix 5)
We never saw "Hello World". Do you see our Problem? What should we do?
With kindly regards,
Meik Hilse
#34
MAX1000 community projects / Re: MAX1000 SDRAM chip
Last post by Antti Lukats - May 26, 2025, 08:58:20 AMouch, I did not check the package size!
yes it is a problem!
yes it is a problem!
#35
Arrow USB Programmer2 / USB Blaster III Compatibility
Last post by Antti Lukats - May 23, 2025, 01:44:17 PMHi
starting from Quartus 25.1 it is possible to use FT2232H based JTAG programmers, like our Arrow USB Programmer without the Arrow DLL installation, it is all included nativly with Quartus both for Windows as for Linux.
To enable the UB3 mode you need to modify the FTDI EEPROM contact for UB3 compatible VID/PID.
Note #1: when once programmed to UB3 mode FT_PROG can no longer access the EEPROM, so you can not change back. But there are Linux tools you can use to erase the EEPROM.
Mote #2: the activity LED on Arrow USB Programmer stops working in UB3 mode with the current PCB versions TEI0004-02. In next PCB revision we will change the LED to support UB3 mode.
starting from Quartus 25.1 it is possible to use FT2232H based JTAG programmers, like our Arrow USB Programmer without the Arrow DLL installation, it is all included nativly with Quartus both for Windows as for Linux.
To enable the UB3 mode you need to modify the FTDI EEPROM contact for UB3 compatible VID/PID.
Note #1: when once programmed to UB3 mode FT_PROG can no longer access the EEPROM, so you can not change back. But there are Linux tools you can use to erase the EEPROM.
Mote #2: the activity LED on Arrow USB Programmer stops working in UB3 mode with the current PCB versions TEI0004-02. In next PCB revision we will change the LED to support UB3 mode.
#36
Trenz Electronic FPGA Modules / Re: Random character printed v...
Last post by Antti Lukats - May 23, 2025, 01:35:02 PMrandom characters may appera when the level shifting CPLD IO bank on TE0790 is not powered. This is controlled with dip.3
#37
Trenz Electronic FPGA Modules / Re: JTAG Not Working On TE0720...
Last post by Antti Lukats - May 23, 2025, 12:53:30 PMone TE0706
DIP.1 should be off but does not matter for JTAG
DIP.2 should be ON to enable ZYNQ JTAG - you have it OFF
DIP.3 should be off but does not matter for JTAG
DIP.4 should be OFF to enable DCDC power supplies - you have it ON
DIP.1 should be off but does not matter for JTAG
DIP.2 should be ON to enable ZYNQ JTAG - you have it OFF
DIP.3 should be off but does not matter for JTAG
DIP.4 should be OFF to enable DCDC power supplies - you have it ON
#38
Trenz Electronic FPGA Modules / Re: JTAG Not Working On TE0720...
Last post by Antti Lukats - May 23, 2025, 12:43:10 PMwe can not see your screenshots.
does Vivado RECOGNIZE the JTAG programmer?
does Vivado RECOGNIZE the JTAG programmer?
#39
Trenz Electronic FPGA Modules / Re: Zynq FSBL at QSPI is unabl...
Last post by Antti Lukats - May 23, 2025, 12:39:07 PMcan you say WHICH SoM of ours are you using?
#40
Trenz Electronic FPGA Modules / Re: Random character printed v...
Last post by Antti Lukats - May 23, 2025, 12:34:09 PMhandled by email