- Welcome to Trenz Electronic GmbH Support Forum.
Recent posts
#1
Trenz Electronic FPGA Modules / Re: TE0745-03-72I31-A connecto...
Last post by JH - December 10, 2025, 07:51:03 AMHi,
yes Modules use ST5 and Carrier SS5 connector. You find ordering number here:
https://wiki.trenz-electronic.de/display/PD/TE0745+TRM#TE0745TRM-BoardtoBoardConnectors
There are no cable between the connectors.
We also offer the altium project of our carrier, in case you want to use it to start with your own project:
https://www.trenz-electronic.de/Downloads/?path=Trenz_Electronic/Modules_and_Module_Carriers/5.2x7.6/5.2x7.6_Carriers/TEB0745/REV02/HW_Design
Links to other documentation and downloads:
https://wiki.trenz-electronic.de/display/PD/TE0745+Resources
br
John
yes Modules use ST5 and Carrier SS5 connector. You find ordering number here:
https://wiki.trenz-electronic.de/display/PD/TE0745+TRM#TE0745TRM-BoardtoBoardConnectors
There are no cable between the connectors.
We also offer the altium project of our carrier, in case you want to use it to start with your own project:
https://www.trenz-electronic.de/Downloads/?path=Trenz_Electronic/Modules_and_Module_Carriers/5.2x7.6/5.2x7.6_Carriers/TEB0745/REV02/HW_Design
Links to other documentation and downloads:
https://wiki.trenz-electronic.de/display/PD/TE0745+Resources
br
John
#2
Trenz Electronic FPGA Modules / TE0745-03-72I31-A connector
Last post by zhouxltx - December 08, 2025, 03:49:41 PMFor TE0745-03-72I31-A board, connector on board is ST5? so on my board, I need to use SS5 connector? are there cable between ST5 and SS5?
Regards
Brian
Regards
Brian
#3
Trenz Electronic FPGA Modules / Re: Petalinux won't boot on TE...
Last post by MA - December 08, 2025, 10:52:01 AMHi,
Have you been able to resolve your issue yet? If not, please feel free to send an email to support@trinz-electronic.de.
br, Manuela
Have you been able to resolve your issue yet? If not, please feel free to send an email to support@trinz-electronic.de.
br, Manuela
#4
Trenz Electronic FPGA Modules / Re: QSPI Programming Issue
Last post by MA - December 08, 2025, 09:25:56 AMHi,
it looks as your CPLD Firmware is not prepaired for JTAG Boot Mode. Can you please update your firmware and try again?
Another option would be to use an older Vivado version (prior to 2021) to programme the QSPI.
br, Manuela
it looks as your CPLD Firmware is not prepaired for JTAG Boot Mode. Can you please update your firmware and try again?
- https://www.trenz-electronic.de/Downloads/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/TE0720/REV04/Firmware
- https://wiki.trenz-electronic.de/display/PD/TE0720+CPLD+Firmware
Another option would be to use an older Vivado version (prior to 2021) to programme the QSPI.
br, Manuela
#5
Trenz Electronic FPGA Modules / QSPI Programming Issue
Last post by mucahityldrm10 - December 05, 2025, 07:41:47 PMHi everyone,
I'm usin te0720-04-62I33ML 4x5 SoM. Also I have te0705 simpllified cariier board. I'm using vivado 2022.1
I wrote a simple standalone LED blink code, and I can debug it normally, and it works. However, when I compile and try to load this code with FSBL for the QSP flash, Vivado gives the following error. It says I can't get the processor into JTAG boot mode. No matter what I do, I can't get the system into JTAG boot mode. It's either in SD card mode or QSP mode. The configuration you've made on the carrier board is as shown in the image below. I need urgent help. Thank you for your support.
I'm usin te0720-04-62I33ML 4x5 SoM. Also I have te0705 simpllified cariier board. I'm using vivado 2022.1
I wrote a simple standalone LED blink code, and I can debug it normally, and it works. However, when I compile and try to load this code with FSBL for the QSP flash, Vivado gives the following error. It says I can't get the processor into JTAG boot mode. No matter what I do, I can't get the system into JTAG boot mode. It's either in SD card mode or QSP mode. The configuration you've made on the carrier board is as shown in the image below. I need urgent help. Thank you for your support.
#6
Trenz Electronic FPGA Modules / Re: Does TE0720 Ethernet work ...
Last post by Antti Lukats - December 05, 2025, 11:27:45 AMHi
thanks for posting the solution and we are glad that it worked!
thanks for posting the solution and we are glad that it worked!
#7
Trenz Electronic FPGA Modules / Re: TE0711 Reference Design - ...
Last post by JH - December 05, 2025, 10:20:39 AMHello,
we try to update our designs one time per year, but unfortunately, we can't always get there right away.
Updates to 25.2 are planned, but I can't tell you any timeline at the moment. During changes from Vitis and petalinux in the future, we have to update our flow for project generation, we working on this task but it takes a little bit time.
You can try to start vivado design from 23.2 with 25.2 when you change in "desgin_basic_settings.cmd"
@set VIVADO_VERSION=2023.2 to @set VIVADO_VERSION=2025.2 and start "_create_win_setup.cmd" again. I think Vivado design generation should work, but for Vitis or petalinux you must do steps manually.
Best regards
John
we try to update our designs one time per year, but unfortunately, we can't always get there right away.
Updates to 25.2 are planned, but I can't tell you any timeline at the moment. During changes from Vitis and petalinux in the future, we have to update our flow for project generation, we working on this task but it takes a little bit time.
You can try to start vivado design from 23.2 with 25.2 when you change in "desgin_basic_settings.cmd"
@set VIVADO_VERSION=2023.2 to @set VIVADO_VERSION=2025.2 and start "_create_win_setup.cmd" again. I think Vivado design generation should work, but for Vitis or petalinux you must do steps manually.
Best regards
John
#8
Trenz Electronic FPGA Modules / Re: SCH-TEIB0006-03-A.pdf
Last post by Thomas D - December 04, 2025, 12:39:59 PMHi
That's correct. 3.3V_FMC is NOT connected to J10. We have corrected this in the schematics.
Thanks for pointing that out.
br
Thomas
That's correct. 3.3V_FMC is NOT connected to J10. We have corrected this in the schematics.
Thanks for pointing that out.
br
Thomas
#9
Trenz Electronic FPGA Modules / SCH-TEIB0006-03-A.pdf
Last post by guirenaud - November 28, 2025, 04:12:42 PMHello
Can you confirm that in the schematics SCH-TEIB0006-03-A.pdf the 3.3V_FMC is not connected to the J10 connector ?
In the schematics page 3 it seems to be connected but further in the schematics nothing connected.
Thanks
Guillaume RENAUD
Can you confirm that in the schematics SCH-TEIB0006-03-A.pdf the 3.3V_FMC is not connected to the J10 connector ?
In the schematics page 3 it seems to be connected but further in the schematics nothing connected.
Thanks
Guillaume RENAUD
#10
Trenz Electronic FPGA Modules / Re: te0630-03
Last post by M Kirberg - November 28, 2025, 03:05:29 PMHi,
this is already dealt with via a separate mail thread, so we will no answer here.
br
this is already dealt with via a separate mail thread, so we will no answer here.
br