- Welcome to Trenz Electronic GmbH Support Forum.
Recent posts
#51
Trenz Electronic FPGA Modules / use prebuilt files
Last post by Lilly_567 - December 15, 2023, 04:24:39 PMHi,
I am really sorry about my maybe stupid questions, but I am a beginner. I was given the TE0715-05-73E33-A SoC Module with the TE0706 Carrier Board. Currently, I am trying to get the board to work with the prebuilt files. I did put BOOT.bin from \test_board\prebuilt\boot_images\03_30_3e_1gb\hello_te0715, image.ub from \test_board\prebuilt\os\petalinux\1GB and boot (the EAGLE configuration one) from the same location as the last one one an SD Card. Then I inserted the SD Card into the slot for it. I left the jumpers J10-J13 on their 1.8V position, as even if I would need HR, this also starts at 1.2V. As S1-1 does not change anything, I left it. I did switch S1-2 (PROGMODE) on, so that the SoC itself is programmed. I switched S1-3 (MODE) on in order to use SD-Boot. Furthermore, I switched S1-4 to on as well. Before plugging anything in, I checked my power supply and it was stable 5V. So I plugged in the power connector jack (J1). I connected XMOD JTAG- / UART-header, JX1 using your adapter to my laptop. To open Vivado, I used your vivado_open_existing_project_guimode script. However, I only get the following errors if I try to use the Hardware Manager:
ERROR: [Labtools 27-2269] No devices detected on target localhost:3121/xilinx_tcf/Digilent/2516330083A6A.
Check cable connectivity and that the target board is powered up then
use the disconnect_hw_server and connect_hw_server to re-register this hardware target.
ERROR: [Common 17-39] 'open_hw_target' failed due to earlier errors.
ERROR: [Labtoolstcl 44-513] HW Target shutdown. Closing target: localhost:3121/xilinx_tcf/Digilent/2516330083A6A
I have two green and one red LED glowing, so the board seems to work. However, it does not seem to do anything, as none of the LEDs change.
If I try to use the scripts from \test_board\console\base_cmd that actually want to put something on the board, I get the same problem.
What am I doing wrong?
Thank you so much for spending time on this in advance.
Kind regards,
Lilly
I am really sorry about my maybe stupid questions, but I am a beginner. I was given the TE0715-05-73E33-A SoC Module with the TE0706 Carrier Board. Currently, I am trying to get the board to work with the prebuilt files. I did put BOOT.bin from \test_board\prebuilt\boot_images\03_30_3e_1gb\hello_te0715, image.ub from \test_board\prebuilt\os\petalinux\1GB and boot (the EAGLE configuration one) from the same location as the last one one an SD Card. Then I inserted the SD Card into the slot for it. I left the jumpers J10-J13 on their 1.8V position, as even if I would need HR, this also starts at 1.2V. As S1-1 does not change anything, I left it. I did switch S1-2 (PROGMODE) on, so that the SoC itself is programmed. I switched S1-3 (MODE) on in order to use SD-Boot. Furthermore, I switched S1-4 to on as well. Before plugging anything in, I checked my power supply and it was stable 5V. So I plugged in the power connector jack (J1). I connected XMOD JTAG- / UART-header, JX1 using your adapter to my laptop. To open Vivado, I used your vivado_open_existing_project_guimode script. However, I only get the following errors if I try to use the Hardware Manager:
ERROR: [Labtools 27-2269] No devices detected on target localhost:3121/xilinx_tcf/Digilent/2516330083A6A.
Check cable connectivity and that the target board is powered up then
use the disconnect_hw_server and connect_hw_server to re-register this hardware target.
ERROR: [Common 17-39] 'open_hw_target' failed due to earlier errors.
ERROR: [Labtoolstcl 44-513] HW Target shutdown. Closing target: localhost:3121/xilinx_tcf/Digilent/2516330083A6A
I have two green and one red LED glowing, so the board seems to work. However, it does not seem to do anything, as none of the LEDs change.
If I try to use the scripts from \test_board\console\base_cmd that actually want to put something on the board, I get the same problem.
What am I doing wrong?
Thank you so much for spending time on this in advance.
Kind regards,
Lilly
#52
UltraScale / Re: TE0807 Starterkit referenc...
Last post by MA - December 12, 2023, 08:59:28 AMHi,
unfortunately I do not have a download link for version 4.3.
What you can do from my point of view is the following:
Please contact the Skyworks support for this version or
read the settings of the clock module from the file "te_Si5345-Register.h". This is a little more complicated but should also work.
best regards,
Manuela
unfortunately I do not have a download link for version 4.3.
What you can do from my point of view is the following:
Please contact the Skyworks support for this version or
read the settings of the clock module from the file "te_Si5345-Register.h". This is a little more complicated but should also work.
best regards,
Manuela
#53
UltraScale / Re: TE0807 Starterkit referenc...
Last post by michielm - December 11, 2023, 03:56:12 PMThanx,
Can you provide me a link to this 4.3 version I cannot find it anywhere on the net...
Gr
Michiel
Can you provide me a link to this 4.3 version I cannot find it anywhere on the net...
Gr
Michiel
#54
UltraScale / Re: TE0807 Starterkit referenc...
Last post by MA - December 11, 2023, 01:53:42 PMThat's right. We need to update the *.slabtimeproj for latest Skyworks versions. The files were created with version 4.3.
#55
CYC1000 community projects / Re: I present a comunity of IN...
Last post by Subcritical - December 10, 2023, 03:10:48 PMHere we can see the USBKeyboard in an 8bit VIC20 implementation:
https://github.com/TheSonders/USBKeyboard
https://www.youtube.com/watch?v=MELJpN_zPD8
https://github.com/TheSonders/USBKeyboard
https://www.youtube.com/watch?v=MELJpN_zPD8
#56
UltraScale / Re: TE0807 Starterkit referenc...
Last post by michielm - December 08, 2023, 03:38:23 PMApparently clockbuilder 3.0 is able to load the project. As said the latest Silabs clockbuilder 4.11 doesn't work...
#57
UltraScale / Re: TE0807 Starterkit referenc...
Last post by michielm - December 08, 2023, 03:00:04 PMHi
Sometimes clocks may have coupling that can be an issue. So my idea was to turn off some clocks (SATA/USB) generated by the Si5345B clock chip which I don't need. However if open clock builder pro project enclosed in the reference design:
https://shop.trenz-electronic.de/trenzdownloads/Trenz_Electronic/Modules_and_Module_Carriers/5.2x7.6/TE0807/Reference_Design/2022.2/StarterKit/TE0807-StarterKit-vivado_2022.2-build_6_20230817092640.zip
Clock builder tells me the project (Si5345-RevB-0807Project.slabtimeproj) is corrupt....
Sometimes clocks may have coupling that can be an issue. So my idea was to turn off some clocks (SATA/USB) generated by the Si5345B clock chip which I don't need. However if open clock builder pro project enclosed in the reference design:
https://shop.trenz-electronic.de/trenzdownloads/Trenz_Electronic/Modules_and_Module_Carriers/5.2x7.6/TE0807/Reference_Design/2022.2/StarterKit/TE0807-StarterKit-vivado_2022.2-build_6_20230817092640.zip
Clock builder tells me the project (Si5345-RevB-0807Project.slabtimeproj) is corrupt....
#58
UltraScale / TE0807 Starterkit reference de...
Last post by michielm - December 06, 2023, 05:11:44 PMAfter using this reference design succesfully:
https://wiki.trenz-electronic.de/display/PD/TE0807+StarterKit
together with this SOM:
https://shop.trenz-electronic.de/en/TE0807-03-7DE21-AZ-MPSoC-Module-with-AMD-Zynq-UltraScale-ZU7EV-1E-4-GByte-DDR4-5.2-x-7.6-cm
I tried to get the VCU working. So i addeded the VCU to the PL, exported a new XSA and imported it into the petalinux project. However strange thing is that the VCU reports an error:
[ 26.602120] al5e 80000000.al5e: Mcu didn't start (no ping after startup, is mcu enabled ?)
[ 26.602120] al5d 80020000.al5d: Mcu didn't start (no ping after startup, is mcu enabled ?)
[ 26.742147] al5e 80000000.al5e: Failed to setup firmware
[ 26.758135] al5d 80020000.al5d: Failed to setup firmware
I only get rid of this error by either starting a petalinux project from scratch or replace the TRENZ FSBL by the default Xilinx ZYNQMP FSBL.
But the reason i ask here is that I'm not sure it's really the FSBL. Using a Trenz TE0803 ZU4EV SOM I was able to get it going with the Trenz FSBL.
I also asked Xilinx but they only told me the VCU is very picky on the applied pll_ref_clk:
https://support.xilinx.com/s/question/0D54U00007g0uDYSAY/cannot-get-vcu-al4dal5e-on-a-trenz-zu4ev-platform-working-using-petalinux-20222
Can you think of a reason why i have so many troubles to get the VCU going?
Gr,
Michiel
https://wiki.trenz-electronic.de/display/PD/TE0807+StarterKit
together with this SOM:
https://shop.trenz-electronic.de/en/TE0807-03-7DE21-AZ-MPSoC-Module-with-AMD-Zynq-UltraScale-ZU7EV-1E-4-GByte-DDR4-5.2-x-7.6-cm
I tried to get the VCU working. So i addeded the VCU to the PL, exported a new XSA and imported it into the petalinux project. However strange thing is that the VCU reports an error:
[ 26.602120] al5e 80000000.al5e: Mcu didn't start (no ping after startup, is mcu enabled ?)
[ 26.602120] al5d 80020000.al5d: Mcu didn't start (no ping after startup, is mcu enabled ?)
[ 26.742147] al5e 80000000.al5e: Failed to setup firmware
[ 26.758135] al5d 80020000.al5d: Failed to setup firmware
I only get rid of this error by either starting a petalinux project from scratch or replace the TRENZ FSBL by the default Xilinx ZYNQMP FSBL.
But the reason i ask here is that I'm not sure it's really the FSBL. Using a Trenz TE0803 ZU4EV SOM I was able to get it going with the Trenz FSBL.
I also asked Xilinx but they only told me the VCU is very picky on the applied pll_ref_clk:
https://support.xilinx.com/s/question/0D54U00007g0uDYSAY/cannot-get-vcu-al4dal5e-on-a-trenz-zu4ev-platform-working-using-petalinux-20222
Can you think of a reason why i have so many troubles to get the VCU going?
Gr,
Michiel
#59
UltraScale / Re: TE820 +TE0706 carrier Ethe...
Last post by pema - December 05, 2023, 02:33:27 PMI got it now working. Needed to enable:
CONFIG_ZYNQ_GEM=y
CONFIG_DM_ETH=y
CONFIG_NET_RANDOM_ETHADDR=y
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842124/U-Boot+Ethernet+Driver#U-BootEthernetDriver-ForZynqMP
CONFIG_ZYNQ_GEM=y
CONFIG_DM_ETH=y
CONFIG_NET_RANDOM_ETHADDR=y
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842124/U-Boot+Ethernet+Driver#U-BootEthernetDriver-ForZynqMP
#60
UltraScale / Re: TE820 +TE0706 carrier Ethe...
Last post by pema - December 05, 2023, 01:22:41 PMSo I made a dumb mistake with an inline comment in the device tree .
I can compile the device tree but I still get no ethernet detected in ubuntu
I can compile the device tree but I still get no ethernet detected in ubuntu
Code Select
Trying to load boot images from dhcp
!!!!!!!!!!!!!!!!!!!!!!!!!!
! Booting from TFTP !
!!!!!!!!!!!!!!!!!!!!!!!!!!
No ethernet found.