TE0821 with TE0706 Carrier Board

[harrx]

Dear,

Could you please help me resolve some the on-boarding issues with TE0821  module(2CG1E- 4 GB DDR) with TE0706 board.

I started with the Test board design v2024.2. I am stuck at the stage of the booting.

My config:
Power: 5V, 1A
Dip switches S1: (1:'1', 2:'0', 3:'0' 4:'1') Default
Reference design:

1. Booting with SD Card: I followed the reference design procedure and copied the 3 required files to the SD card Boot (1st) Partition. Nothing in the Root (2nd) partition. As soon as I power up the device with SD card inserted, all LEDs (incl. Ethernet) starts blinking and I see only "?" on the Serial terminal. Taking out the SD card, all LEDs are stable again.

2. QSPI Boot: TE::pr_program_flash -swapp u-boot ,, also does not work for me. I get the error "Flash programming is not supported in the selected boot mode". I tried switching S1-3:'1', but this does not help also.

3. Simple JTAG programming also does not work. Programming Baremetal application with Vitis also generates the error: "Flash programming is not supported in the selected boot mode, switch mode to JTAG".

Could you please help me resolve this issue. Point#03 is the most cirtical to be able to quickly load App changes from Vitis without the need to boot the whole device.

Best regards,
Haris.

[harrx]

Dear,

Could you please help me resolve some the on-boarding issues with TE0821  module(2CG1E- 4 GB DDR) with TE0706 board.

I started with the Test board design v2024.2. I am stuck at the stage of the booting.

My config:
Power: 5V, 1A
Dip switches S1: (1:'1', 2:'0', 3:'0' 4:'1') Default
Reference design:

1. Booting with SD Card: I followed the reference design procedure and copied the 3 required files to the SD card Boot (1st) Partition. Nothing in the Root (2nd) partition. As soon as I power up the device with SD card inserted, all LEDs (incl. Ethernet) starts blinking and I see only "-?-" on the Serial terminal. Taking out the SD card, all LEDs are stable again.

2. QSPI Boot: TE::pr_program_flash -swapp u-boot ,, also does not work for me. I get the error "Flash programming is not supported in the selected boot mode". I tried switching S1-3:'1', but this does not help also.

3. Simple JTAG programming also does not work. Programming Baremetal application with Vitis also generates the error: "Flash programming is not supported in the selected boot mode, switch mode to JTAG".

Could you please help me resolve this issue. Point#03 is the most cirtical to be able to quickly load App changes from Vitis without the need to boot the whole device.

Best regards,
Haris.

[harrx]

Dear,

Could you please help me resolve some the on-boarding issues with TE0821  module(2CG1E- 4 GB DDR) with TE0706 board.

I started with the Test board design v2024.2. I am stuck at the stage of the booting.

My config:
Power: 5V, 1A
Dip switches S1: (1:'1', 2:'0', 3:'0' 4:'1') Default
Reference design:

1. Booting with SD Card: I followed the reference design procedure and copied the 3 required files to the SD card Boot (1st) Partition. Nothing in the Root (2nd) partition. As soon as I power up the device with SD card inserted, all LEDs (incl. Ethernet) starts blinking and I see only ? on the Serial terminal. Taking out the SD card, all LEDs are stable again.

2. QSPI Boot: TE::pr_program_flash -swapp u-boot ,, also does not work for me. I get the error "Flash programming is not supported in the selected boot mode". I tried switching S1-3:'1', but this does not help also.

3. Simple JTAG programming also does not work. Programming Baremetal application with Vitis also generates the error: "Flash programming is not supported in the selected boot mode, switch mode to JTAG".

Could you please help me resolve this issue. Point#03 is the most cirtical to be able to quickly load App changes from Vitis without the need to boot the whole device.

Best regards,
Haris.

[M Kirberg]

Please look at the boot mode setting on the TE0821 CPLD. Setting S1:3 is not enough you need to be in JTAG mode thats what the error says, and you are most likely in QSPI mode.

PGOOD is used as additional bootmode pin in standard firmware, you need to "set" this signal also to the right value.