Author Topic: TE0723-02 Drawing file  (Read 3736 times)

leirbag

  • Active Member
  • *
  • Posts: 5
TE0723-02 Drawing file
« on: June 17, 2016, 07:20:57 AM »
Hi admins,

It is difficult to figure out the header number ID (J1, J2, etc.) and its pinout in other place than the board itself. Unfortunately, this info not appear in the TE0723-02 Drawing file, http://www.trenz-electronic.de/fileadmin/docs/Trenz_Electronic/TE0723/REV02/Hardware%20Design/AD-TE0723-02.PDF

Is there any chance to show this info at this file or in another new one?

Than you in advance,

Gabriel Solsona

Thorsten Trenz

  • Administrator
  • Full Member
  • *****
  • Posts: 155
    • Trenz Electronic GmbH
Re: TE0723-02 Drawing file
« Reply #1 on: June 17, 2016, 08:18:24 AM »
Hi,
will this help?
https://wiki.trenz-electronic.de/display/OSHW/TE0723

In any case we will add the header information in the assembly drawing. It will get updated soon.

Best Regards
Thorsten Trenz

leirbag

  • Active Member
  • *
  • Posts: 5
Re: TE0723-02 Drawing file
« Reply #2 on: June 17, 2016, 09:12:35 AM »
Dear Thorsten,

First of all, thank you indeed for the promptly answer. About the alternative you have proposed, I must say that I was aware of this page but regrettably it does refer to the first version. I mean, for instance, the PMOD header does not exist.

I beg you address this issue as fast as you can, due to we need to work with such information intensively in these days.

Once more time, thank you very much,

Gabriel Solsona

Antti Lukats

  • Hero Member
  • *****
  • Posts: 559
Re: TE0723-02 Drawing file
« Reply #3 on: June 17, 2016, 11:06:35 AM »
will be updated, the assembly diagrams generated from CAD do not show the headers that are set as "not mount" in schematic :( we look what we can do to add the info

leirbag

  • Active Member
  • *
  • Posts: 5
Re: TE0723-02 Drawing file
« Reply #4 on: June 17, 2016, 11:09:47 AM »
If updating https://wiki.trenz-electronic.de/display/OSHW/TE0723 is the easiest way for you, it is ok for us too!

Thank you!

Antti Lukats

  • Hero Member
  • *****
  • Posts: 559
Re: TE0723-02 Drawing file
« Reply #5 on: June 17, 2016, 11:33:27 AM »
what info you miss the most? the pinout is in schematic, what is missing, are the measurements for the placement of the added pmod connector only

leirbag

  • Active Member
  • *
  • Posts: 5
Re: TE0723-02 Drawing file
« Reply #6 on: June 17, 2016, 11:39:45 AM »
Well, at this moment, pinout and header enumeration in a sketch would be enough.

But in the near future and if everything goes well, we'll need to design an auxiliary piggyback PCB on top of the TE023 so, coordinates placement of the headers will be needed.

At your convenience!

Thank you again, Antti!


leirbag

  • Active Member
  • *
  • Posts: 5
Re: TE0723-02 Drawing file
« Reply #8 on: June 17, 2016, 12:42:16 PM »
Awesome!

Enough!

Thank you so much!

Gabriel Solsona